Skip to content

HVAC Installer 1

Get an installer who can be trusted on a complete changeout.

For new and early-career installers. By the end you can survey a site, size and fabricate duct, set and connect equipment, braze and pressure test a line set, and commission the finished system.

Length
40 hours
Class size
Small classes (12 max)
Austin
Sat 7am-7pm, Mon-Fri 4pm-9pm
Houston
Mon-Fri 8am-5pm
See all skills verified in this bootcamp ↓
Choose a location first

Austin runs nights and Saturdays. Houston runs weekdays.

Dates coming soonWe’re scheduling the first cohorts now. Contact us to reserve seats for your team, or to hear as soon as dates open.

Contact us to enroll

Use the email you’re booking with

Continue to checkout

Secure checkout

By enrolling you agree to our Terms and Privacy Policy.

Skills we train and verify

  • Survey a Site and Plan an Installation
  • Size and Lay Out a Duct System
  • Fabricate Sheet Metal Duct and Fittings
  • Install, Seal and Insulate Duct
  • Set and Secure Equipment
  • Route, Braze and Pressure Test a Line Set
  • Install a Vent System to Code
  • Connect Gas Piping and Verify Combustion Air
  • Install Condensate Drainage and Safety Switches
  • Wire Line and Low Voltage for New Equipment
  • Cut Structural Penetrations
  • Install and Set Up Thermostats and Controls
  • Charge and Commission a New System
  • Document Commissioning and Hand Off to the Customer
  • Complete a Full Installation to Plan

Credentials

Train America HVAC Installer 1 Course Credential

Course details

Course modules

Austin: SAT 7am-7pm, MON-FRI 4pm-9pm
Houston: MON-FRI 8am-5pm

  1. 01

    Installation Safety and Site Preparation

  2. 02

    Duct Design, Fabrication and Installation

  3. 03

    Installing the Cooling Side and Heat Pump Setup

  4. 04

    Line Sets, Brazing and Equipment Setting

  5. 05

    Installing the Heating Side - Venting and Fuel Connection

  6. 06

    Condensate Drainage Systems

  7. 07

    Electrical Procedures for Installation

  8. 08

    Charging the New System by Superheat and Subcooling

  9. 09

    Start-Up, Commissioning and Post-Install Checkout

  10. 10

    Installation practice

Prerequisites

HVAC Tech Level 1 recommended. Attendees must be 18 or older and employed by the enrolling company.

Bring

Your tools and PPE.

We provide

Sheet metal tools, brazing and vacuum gear, install bays and materials.

What to wear

Attendees should wear jeans and closed-toe shoes, preferably work boots, and come dressed each day as they would for a call at a customer's home, representing your company.

Where

Austin Training Center
6807 Elroy Rd #201, Del Valle, TX 78617

Houston Training Center
14420 W Sylvanfield Dr, Suite 110, Houston, TX 77014

Cancellation

Cancel 30+ days out for a refund (less 3%), or 7+ days out to change dates. For 6+ seats: 60 and 21 days. Terms →

Enrolling a crew?

For invoicing, or seats before you have names, ask about a Training Services Agreement: training@trainamerica.com

Not ready to book yet?

See the training or talk it through. We reply within one business day.

  • Training center tour
  • Course demo and deep dive
  • Meet with us or ask a question
Talk to us first →

Lock in member pricing.

  • Join for free
  • Recruit our students
  • A seat on our Industry Advisory Board

Order 5 bootcamps by 12/31/27 to keep it. Terms

Through 2027
$1,747$3,495
After 2027
15% off, for good
Join free to lock in $1,747